The short answer
- Grinding — metal on metal. The pad is finished. Stop driving and inspect today; every stop scores the disc.
- Squealing — often a wear indicator, glazed pads or a dry slide pin. Not always urgent, always worth checking.
- Pulsing pedal or a shaking wheel — uneven pad deposit on the disc, or a disc that is worn thin and running out of true.
- Measure before you buy. Pad thickness and disc thickness decide the job, not the noise alone.
What each noise is telling you
Brakes are the one system where the symptom usually names the fault. A grind is steel on steel. A squeal is a vibration at the pad edge, or the small metal tab some pads carry to squeal on purpose when the friction material runs low. A pulse through the pedal is a change in friction as the wheel turns.
| What you notice | What it usually is | How urgent |
|---|---|---|
| Grinding, worse under light braking | Friction material gone; backing plate on the disc | Stop driving. Pads and almost certainly discs. |
| Squeal at low speed, stops when you press harder | Wear indicator tab, glazed pad surface, dry slide pins | Inspect within days. |
| Pedal pulses, steering wheel shakes | Uneven friction deposit or disc run-out | Safe to drive gently, fix soon. |
| Car pulls to one side when braking | A sticking caliper or a collapsed hose on one side | Inspect now — braking is uneven. |
| Pedal feels soft or sinks | Air or a fluid leak in the hydraulic system | Do not drive. This is a failure, not a wear item. |
| Handbrake needs more clicks, or the car rolls on a slope | Rear shoes out of adjustment, or a stretched cable | Adjust or repair this week. |
The ten-minute check you can do yourself
You do not need a workshop to answer the only question that matters — how much friction material is left. Jack one corner at a time, support it properly on an axle stand, and look through the gap between the wheel spokes at the caliper.
- Look at the pad. On most calipers you can see the outer pad against the disc. New pads commonly start with around 10 to 12 mm of friction material; below 3 mm, plan the job.
- Check both pads on that corner. A caliper that slides badly wears the inner pad while the outer looks fine. If you cannot see the inner pad, take the wheel off.
- Run a finger down the disc face. A lip at the outer edge says the disc has worn. Deep grooves you can catch a fingernail in mean it is finished.
- Look at the fluid level. It drops slowly as pads wear. A level that has fallen quickly, or fluid on the inside of a tyre, is a leak — not wear.
- Check the tyre and the wheel bearing. A worn bearing can imitate a brake noise. Rock the wheel at the top and bottom; any movement means investigate before blaming the brakes.
Cannot see the pads? Ask a tyre shop to put the car on a lift, or send a photo to a parts counter.
Pads: what is in the box, and why cheap ones squeal
A pad set is not just friction blocks. A good set includes shims or an anti-squeal layer on the back plate, the retaining clips, and sometimes new slide-pin boots. Reusing tired clips and dry pins is the most common reason a fresh set of pads squeals within a month.
Compound matters more than brand loyalty. Ceramic pads run cooler and quieter and make less dust, which suits a light car doing short city trips. Semi-metallic pads bite harder from cold and take heat without fading, which is what a loaded van or a heavier SUV needs. Neither is "better"; the wrong one for the car is what causes complaints.
Discs: thickness, lips and the truth about "warped" discs
Almost no disc is actually bent. What owners call a warped disc is usually uneven friction deposit — a patch of pad material baked onto one part of the surface after a hard stop, so the pad grips harder as the wheel turns and the pedal pulses. The other common cause is corrosion: a car that sits for weeks develops a rough ring where the pad was resting, and that ring never beds back in.
A disc is replaced when it is below its minimum thickness, which is stamped on the hub face or listed for the part, when it is deeply scored, when it has a visible crack, or when it is worn into a step at the edge. Skimming is possible only if there is enough material left afterwards — and on a disc already near its limit, machining simply moves the replacement forward a few months.
Replace discs in pairs on the same axle. Two discs of different thickness and surface give different braking at each wheel, and the car will pull under hard braking even if both "work".
Shaking: is it the front or the rear?
Where you feel it tells you which end to inspect. Shaking through the steering wheel points at the front brakes. A pulse through the pedal and the seat, with the wheel steady, points at the rear. A shake that appears at speed without braking is a different problem — wheel balance, a bent rim, a tyre with a flat spot, or a worn bearing — and brake work will not fix it.
Two cheap things are worth ruling out first: a wheel refitted without cleaning the hub face, and wheel nuts torqued unevenly. Both distort the disc slightly and both disappear when the wheel is refitted properly.
What the job involves
| Job | What is involved | What moves the price |
|---|---|---|
| Front pads | Pad set, clips, cleaning and greasing the slide pins, checking the caliper pistons | Compound, brand, whether the caliper needs a rebuild |
| Front pads and discs | As above plus discs in pairs, and the caliper bracket comes off | Disc type (plain or grooved), and whether the hub faces need cleaning |
| Rear pads and discs | Same on the rear axle, often with an electronic parking brake to retract | Whether the parking brake needs a service tool or a manual procedure |
| Rear shoes and drums | Drum removal, shoe set, springs and self-adjuster, drum condition | Drums are often not included and are the surprise line on the bill |
| Caliper or hose | One caliper, a hose, fluid, bleeding the system | One side or both; a sticking caliper usually means new pads on that side too |
| Brake fluid change | Fluid flushed through all four corners and bled in order | Fluid specification and whether the ABS unit needs a scan-tool bleed cycle |
We publish no amounts here. Brake parts differ enormously by brand, by whether a fitting kit is included, and by how much of the disc and hardware has to be renewed rather than reused. A quote is only comparable against the same brand and the same job list.
Fluid, hoses and the ABS light
Brake fluid absorbs moisture over time, which lowers its boiling point and can make the pedal go long after a hard descent. Most manufacturers call for a change every two years regardless of mileage, and it is the cheapest brake job there is. Rubber hoses perish from the inside out; a hose that is soft, cracked or bulging at the crimp is a leak waiting to happen.
If the ABS light joins the brake warning light, stop treating it as a wear question. A wheel speed sensor or its wiring, a low fluid level or a pump fault will all do it, and none of them are fixed by new pads. Have the codes read before authorising parts.
Model notes
| Model family | What owners notice | What that means at the parts counter |
|---|---|---|
| i10, Picanto, Atos | Light, front-biased brakes, rear drums on many versions | Small pad sets; check whether the car has rear drums before ordering rear discs |
| i20, Rio, Accent, Getz | Pads last well unless the car lives in stop-start traffic | Two pad shapes across the years; the VIN settles it |
| Elantra, Cerato, i30 | Bigger front discs, quiet but dustier pads | Ceramic compound is a common choice; discs often replaced with the second pad set |
| Tucson, Sportage, ix35 | Heavier car, hotter brakes, more caliper work with age | Semi-metallic pads and caliper hardware worth replacing rather than reusing |
| H-1 and H-100 | Loaded use, long descents, heat | Pads and discs are a working part of the vehicle, not a comfort item — specify accordingly |
How to bed in new pads
Find an empty straight road. From a moderate speed, brake firmly but not harshly down to walking pace, and repeat this around eight to ten times with a short gap between stops so the brakes cool a little. Then drive for several minutes without touching the brakes, letting air do the cooling. Do not sit with the pedal held down at a standstill during the first hundred kilometres: that bakes a patch of pad material into the hot disc and recreates the pulse you just paid to remove.
Frequently asked questions
Can I drive with grinding brakes?
Only to the nearest safe place. Grinding means the friction material is gone and steel is cutting into the disc. Every stop makes a reusable disc into scrap.
Do new pads always mean new discs?
No — but more often than owners hope. Below minimum thickness, deeply scored, cracked or lipped discs are replaced. After grinding, assume both.
Why does it shake only when I brake?
Uneven friction deposit on the disc, or run-out from a worn disc or a dirty hub face. It is friction, not a bent disc, in most cases.
Ceramic or semi-metallic pads?
Ceramic for light cars that mostly see city driving: quieter and cleaner. Semi-metallic for heavier cars, vans and towing, where cold bite and heat tolerance matter more.
How long should brakes last?
Front pads commonly outlast rear pads by around half again, and a light car driven gently can go a long time between sets. Traffic, load and hills shorten it more than mileage suggests. Measure, do not count.
General information only. Brake specifications, minimum disc thickness and fluid requirements differ by model, year and market, and brake work is safety-critical. Have the system inspected by a qualified technician, compare any quote against the job list above rather than a figure from the internet, and never work under a car supported only by a jack.