The short answer
- Cranks but will not start hot, restarts after cooling — crank or cam position sensor.
- Idle hunts or drops at a stop, then recovers — dirty idle control valve or throttle body, or a vacuum leak.
- Shudders under load, flashing engine light — ignition misfire: plug or coil on the stored cylinder.
- Rough only when cold — coolant temperature sensor, intake gasket or breather blockage.
- Whitish smoke and a misfire that will not move — compression: stop driving and test it.
Start with the pattern, not the parts
An engine needs three things: fuel, air at the right ratio, and a spark at the right moment. Every fault in this guide takes one of those away, and the pattern of when it happens tells you which. Two questions do most of the work: is it worse hot or cold, and is it worse at idle or under load.
| What happens | What it points at | How to confirm |
|---|---|---|
| Cranks, no start when hot, starts after cooling | Crank or cam position sensor | Rev counter dead while cranking; live data shows no engine speed |
| Idle drops or hunts at a stop, sometimes stalls | Idle control valve, throttle body carbon, vacuum leak | Idle changes when you press the brake; hiss at idle; cleaner test |
| Shudder or hesitation under acceleration | Coil or plug on one cylinder | Code names the cylinder; swap the coil and see if the code follows |
| Rough only from cold, smooth when warm | Coolant temperature sensor, intake gasket, PCV | Live data cold versus warm; check the intake for a leak |
| Loss of power with a whistle, lean codes | Split intake hose or vacuum line | Smoke test, or a visual check of the breather hose |
| One cylinder dead, no change when the coil is swapped | Injector, wiring or compression | Compression and leak-down test before buying anything |
| Stalls while driving, restarts instantly | Loose earth, chafed crank sensor wire, failing relay | Wiggle test on harnesses; check earth straps and engine bay fuse box |
Crank and cam sensors: the "leaves you stranded" fault
The crank sensor tells the engine control unit where the crankshaft is and how fast it is turning; the cam sensor tells it which stroke each cylinder is on. When the crank signal drops, the engine stops instantly — no stutter, no warning, and often no fault code until the failure repeats.
The signature is heat. The sensor fails when hot, the engine cranks without firing, and twenty minutes later it starts first turn. While cranking, the rev counter does not move at all: that single observation separates a position sensor from a fuel pump, an immobiliser or a weak battery. A scan tool showing engine speed while cranking confirms the same thing in one screen.
Cam sensor faults are gentler. The engine may run, but with hard starting, poor idle and a code for cam-to-crank correlation. Either way, the part is inexpensive and the diagnosis is quick. What you should not do is replace the fuel pump because the car "will not start when hot" without checking whether there is any rpm signal.
Idle control valve and throttle body
An idle control valve is a small motorised or solenoid valve that lets a measured amount of air past a closed throttle so the engine can idle. Carbon from the crankcase breather builds up on the valve seat and in the throttle bore, and the engine loses the ability to hold a steady idle: it dips when you come to a stop, hunts up and down, or stalls when the air conditioning cuts in.
Cleaning is the first step, not replacing. Remove the valve or the throttle body, clean the passages with throttle-body cleaner and a soft brush, and refit with a new gasket if the old one is hardened. On many modern engines the throttle body is electronic and the learned idle position has to be reset afterwards — either with a scan tool or with a documented pedal-and-ignition sequence. Skip that step and the car idles high for a week and then settles, which owners often misread as a failed part.
A vacuum leak imitates a sticky valve: a split breather hose, a perished intake gasket or a leaking brake booster hose lets unmetered air in, so the idle rises and the fuel trims go lean. If the idle changes when someone presses the brake pedal, the booster or its hose is suspect.
Coils, plugs and injectors
An ignition misfire is the one fault that damages something else while you drive: unburnt fuel and oxygen reach the catalytic converter and cook it. That is why a flashing engine light means stop soon, while a steady light with a slight shudder means book it in.
The code names the cylinder, not the part. The fastest free test is to swap the coil from the misfiring cylinder with another and clear the code: if the misfire moves, the coil is at fault; if it stays, the fault is the plug, the injector, the wiring or compression on that cylinder. Look at the plug when it comes out — a single wet or black plug tells you the same thing without a scan tool.
Injectors fail less often than coils, but they do clog. A cylinder with good spark and good compression that still misfires at idle usually has a lazy injector, and a professional clean or a replacement settles it. Do not replace all four on a guess.
The free checks before the parts counter
- Read the codes and the freeze-frame data. Engine speed, load and temperature at the moment of the fault narrow the list faster than any forum post.
- Look at the intake path. A cracked breather hose between the air box and the engine is a common and cheap cause of a rough idle.
- Check the air filter and the intake for obstruction. A filter packed with dust upsets the air metering.
- Listen at idle. A hiss is a vacuum leak; a ticking is ignition; a low thump is exhaust or a mount.
- Check the battery and earth straps. Low voltage makes sensors lie and coils weak, and a corroded earth causes stalling that no part will fix.
What each repair involves
| Part | What the job involves | What moves the price |
|---|---|---|
| Crank sensor | One bolt and a connector, sometimes a heat shield or belt cover in the way | Access; on some engines the sensor sits behind a pulley |
| Cam sensor | One bolt, one connector, usually at the top of the head | OEM-spec versus aftermarket, and the seal or O-ring |
| Idle control valve | Clean first, replace only if the motor or seat is worn | Whether a gasket is included and whether a relearn is needed |
| Throttle body | Clean the bore, refit, relearn the idle | Electronic throttle bodies need a scan tool step |
| Ignition coil | One coil per cylinder, usually one bolt and a connector | One coil versus a set of the same age |
| Spark plugs | A set in the correct heat range and gap | Plug type specified for the engine code |
| Injector clean or replace | Clean on the car, or remove the rail and replace the injector | Seals, and whether the rail has to come off |
We publish no amounts. Sensor and ignition prices vary widely by brand and by whether the part is OEM-spec or aftermarket, and the labour depends entirely on access. Ask for the part number against the VIN so the quote is for the part that is actually on your engine.
Model notes
| Model family | Common complaint | What to check first |
|---|---|---|
| i10, Picanto, Atos | Idle dips when the air conditioning cuts in; hot no-start | Throttle body carbon, then crank sensor if it will not fire hot |
| i20, Rio, Accent, Getz | Misfire under load, rough cold idle | Coils and plugs by cylinder code; intake gasket for cold-only roughness |
| Elantra, Cerato, i30 | Hesitation, lean codes, idle hunt | Vacuum and breather hoses, then throttle body clean |
| Tucson, Sportage, ix35 | Misfire with heat, coil failures | Coil-on-plug condition and plug gaps at the specified mileage |
| H-1, H-100, K2700 | Diesel: rough running, smoke, low power | Fuel filter and water, injector condition, then a scan for rail pressure |
Frequently asked questions
Why will it not start when hot?
A position sensor failing with heat is the classic. If the rev counter does not move while cranking, start there rather than at the fuel pump.
Does a dirty idle valve cause stalling?
Yes, especially when you lift off or come to a stop. Clean the valve and throttle bore, then relearn the idle.
Can I drive with a misfire?
Gently and briefly with a steady light. Not with a flashing light — that is unburnt fuel cooking the catalytic converter.
Why only when cold?
Cold running uses a different fuel strategy, so a tired coolant temperature sensor or a leaking intake gasket shows up then and disappears when warm.
How do I find a vacuum leak?
Listen for a hiss, check the breather hose and the brake booster by pressing the pedal, then have a smoke test done if the visible hoses are sound.
General information only. Fault codes, sensor locations and relearn procedures differ by engine, model year and market. Use the code and the vehicle's own data before replacing parts, and have persistent misfires or stalling diagnosed by a qualified technician.