Korean Auto Guide Hyundai & Kia ownership, explained
Fault Diagnosis

Key Not Detected or Immobiliser Fault: It Will Not Start

"Key not detected" and a car that cranks without firing are two different refusals, and both are usually cheap to fix. Here is the order to work through them — including the trick that starts a car with a dead fob.

By Korean Auto Guide editorial team Updated 16 November 2026 8 min read

The short answer

  • Press the start button with the fob itself. The passive chip is read through the button even with a flat battery.
  • Button dead, battery fine? Check the brake (or clutch) pedal switch — start with whether the brake lights work.
  • Cranks but will not fire, immobiliser light on? The key is not matched: try the spare key first.
  • Both keys refused? Now it is the car's receiver or module, and that needs a diagnostic session, not a locksmith guessing.

Which refusal is it?

Three things can stop a Hyundai or Kia from starting, and they sound different. Naming the right one saves both time and money.

What happensWhat the car is telling youFirst move
Dash says "key not detected", button does nothingThe car cannot see a valid fobHold the fob against the start button
Button does nothing, no message, dash lights up normallyStart request not accepted — usually the pedal switchCheck the brake lights
Single click, then nothingStarter or its main feedBattery and earth, then starter
Cranks strongly, will not fire, key symbol flashingImmobiliser has not matched the keyTry the spare key
Cranks strongly, will not fire, no key symbolFuel or ignition fault, not the keySee the cranking-but-not-starting checks

The fob: simple causes first

  1. Fob battery. A coin cell that is two or three years old can be intermittent, and cold weather finishes it. Replace it before anything else — it is inexpensive and takes a minute.
  2. Press the button with the fob. Holding the fob against the start button lets the car read the passive transponder through the antenna in the button, which works with no battery at all in the fob.
  3. Try the spare key. This single test tells you whether the fault is in the key or in the car, and it decides everything that follows.
  4. Remove interference. A fob in the same pocket as a phone, or a bag with a laptop, can be shielded. So can a fob left next to a wireless charger or a strong transmitter.
  5. Check for moisture. A fob that has been through the wash will often work intermittently before it stops. Dry it, replace the battery, and try again before condemning it.

The pedal switch nobody suspects

On a push-button car the start request is conditional: the control unit needs to know the brake pedal is pressed (or the clutch, on a manual). A worn or misadjusted brake light switch will let the dash light up and refuse to crank, with no message on most models. The giveaway is that the brake lights do not come on, or come on only when you press hard.

On some models this same switch also feeds the transmission interlock and the cruise control, so a failing switch can show up as "will not come out of park" or "cruise control will not set" a few weeks before the start failure. If your brake lights are working but the button does nothing, the switch is less likely — but a scan tool will show whether the start request is being received.

The immobiliser side

Hyundai and Kia vehicles use a transponder in the key and a receiver coil around the ignition barrel or in the button. The body control module and the engine control unit both hold a coded identity; if any of the three disagrees, the engine will not run.

CauseBehaviourWhat fixes it
Fob battery flatKey not detected; may still work pressed against the buttonNew coin cell
Damaged key chipOne key refused, the other worksNew key cut and programmed
Receiver coil / antennaAll keys refused in the same wayCoil replaced, then keys re-tested
Body control module faultIntermittent, often with other electrical odditiesModule diagnosis, reprogramming or replacement
Lost coding after a battery change or jump startRefused immediately after electrical workRe-programming; usually a dealer or a specialist with the right tool

Jump-starting can be the cause, not the cure

Connecting a booster with the ignition on, or reversing the leads even briefly, can disturb module coding and fuse the main link. Connect positive to positive, negative to a good earth away from the battery, and never jump a car with the ignition switched on if you can avoid it.

If the wheel will not turn and the button will not work

A steering lock that is engaged with pressure on the wheel can prevent the start sequence. Turn the wheel firmly against the stop while pressing the button. This is a common false alarm after parking with the wheels against a kerb.

What the repair involves

JobWhat is involvedWhat moves the bill
Fob batteryA coin cell and two minutesNothing — always try this first
Brake / clutch pedal switchSwitch replaced, usually under the dashAccess and whether the switch needs adjustment
New key or fobKey cut, transponder programmed, remote pairedWhether the car needs a security code, and whether both keys must be present
Receiver coilTrim around the barrel or button removed, coil replacedDashboard trim work, and re-testing every key afterwards
Module programmingDiagnostic session with a manufacturer-level toolWhether the module can be reprogrammed or has to be replaced and coded
StarterUnit or solenoid replacedAccess; check the earth strap at the same time

Ask for the fault codes before any programming. A module replacement that is authorised on a hunch is the most expensive outcome in this guide, and on these cars the key coding is frequently recoverable without replacing anything.

Avoiding a repeat

  • Replace both fob batteries at the same time every few years, before they fail in a car park.
  • Keep the spare key working and stored away from the car — a spare that has never been used is a plan, not a spare.
  • Do not store the fob against a phone or a wireless charger.
  • Note the emergency start position for your model in the owner's manual — usually the button or a marked console area.
  • Fix electrical oddities early. An intermittent body control module fault usually shows up as a window or lamp misbehaving before it stops the car.

Frequently asked questions

How do I start the car with a dead fob?

Press the start button with the fob itself, or hold the fob against the marked area in the console. The passive chip works without a battery.

Why does the button do nothing at all?

Most often the brake or clutch pedal switch. Check whether the brake lights work when you press the pedal.

What does the key symbol mean?

The immobiliser has not matched the key. It may crank without firing, or refuse to crank. Try the spare key before anything else.

Can a phone interfere with the key?

It can shield a low-battery fob in the same pocket or bag. Test with the fob in your hand, away from other electronics.

Do I have to go to a dealer for a new key?

Not always. Many independent locksmiths can program these keys with the right equipment, but ask whether they can program both the transponder and the remote before you commit.

General information only. Smart-key behaviour, emergency start positions and programming procedures differ by model and model year. Immobiliser and key programming require manufacturer-level equipment; check the owner's manual for your car's specific procedure.